Package Includes:
- Left controller Grip
- Mouse
- Wireless Receiver Stick
- Quick Start Card
Quick Start Card
The Mouse and the Grip each take one AA battery(not included in the package). Carefully open the battery bays under the Mouse and Grip and insert one battery in each. Remember battery flat sides go to the spring end.
Scorch on 360
Plug your wired XBox 360 controller into the Dongle. Plug the Scorch USB Dongle into one of the front USB ports on the XBox 360. Press the power button on the top of the Mouse and press the Guide button on the Grip to power up.
Pressing the Mouse wheel down is your Right Analog Stick Down.
Press and hold the F button and roll the wheel forward to increase the sensitivity.
To decrease sensitivity press and hold the F button and roll the wheel backward.
Note that there are 20 sensitivity adjustments when on the Xbox 360.
Game Smoothness
For the smoothest game play we recommend you press and hold the F button and roll your mouse wheel back and forth to find the position that the game stops to roll. Gamers call this F0. This is your reference point and will be the smoothest mouse setting.
Roll the wheel forward a couple of clicks to increase your mouse speed. Some games may require different sensitivity adjustments to make your game play as smooth and fast as possible. When you release the F button the setting will be stored in the Mouse memory. Each time you use the Mouse it will reload your sensitivity settings. To make your game play as smooth as possible there are 20 setting adjustments on the Xbox 360.
Rapid Fire
To enable or disable rapid fire, press and hold the F button then press RT (Left Click)
You can adjust the shot repetition in the Scorch configuration software.
To turn on or off the mouse wheel features – press and hold mouse F and press mouse wheel down.
Scorch on PC
Plug in the USB Stick into your computer USB port.
The first time you plug the Stick into the port you will notice that MS Windows shows a message on the bottom right corner that says – “Installing New Hardware.” Allow Windows to finish installing your drivers by selecting all the default options. When Windows has finished you will see a message on the bottom right corner that says “Your device is now ready to use.” It may go through several pop-up windows to finish the device installation.
Press the START button on the top of the Mouse and press the Guide button on the Grip to power up.
Use the Scorch config utility to change and set Grip or Mouse buttons to the button layout you want. Most games also allow you to change keyboard hot keys that will be matched on your controller. The Mapper configuration Software is free and can be found and downloaded from our website at www.Bannco.com.
Scorch resolution setup
To increase the Mouse resolution press and hold the F button and roll the mouse wheel forward.
To decrease the resolution press and hold the F button and roll the wheel backward.
There are four CPI mouse resolutions to choose from. To increase the laser resolution press and hold the F and roll the mouse wheel forward. To decrease the laser resolution press and hold the mouse F button and roll the wheel back. The resolution is stored in memory so it does not need to be set each time you use your controller.
Power Saving
The Mouse or Grip will auto shut off after 8 minutes of no button or mouse movement activity.
When the LED lights on the Mouse or Grip flash fast, it indicates a low battery.
Matching
Each Mouse and Grip can be matched with the USB Stick. The factory does matching however you may need to match them when the following happens to you:
You get a replacement Mouse, Stick or Grip, or, the devices loose their sync together.
Note: You don’t need to match every time you use them.
To match the devices:
a) First press the small button on top of the Stick. A green LED on Stick will flash quickly to indicate it is waiting to be matched.
b) Then within 10 seconds, press the small button on the underside of the Mouse.
A solid LED indicates the Mouse is matched.
c) Press the small button on top of the Stick again. Now press the small button in the Grip battery bay to complete the matching.
If you miss pressing a device button, after 10 seconds the Stick LED returns to normal.
Note: Each time you press the Stick button only one device can be matched so the Mouse and Grip need to be matched in these steps.
Firmware and Software
Scorch can be firmware upgraded and can also be configured by software. From time to time we may release free firmware upgrades to improve performance. This will be posted on our web site with an explanation of any features or improvements for your consideration.For more detailed information about how to upgrade and configuration your Scorch check our Scorch sections on the official bannco site.
Troubleshooting
If your Scorch controller is not functioning:
- Go to the official site www.bannco.com it is a wealth of helpful information.
- Make sure the USB Dongle is plugged in all the way into the USB port.
- Make sure that the Mouse laser slot is kept clean of any fuzz or hairs.
- Make sure the Mouse and Grip are matched to the USB Dongle.
- Make sure to use fresh AA batteries in the Mouse and the Grip.
- Try to take out the Dongle and plug it back in again.
- Restart your PC or Xbox360.
If any of above does not solve your problem, contact bannco technical support at support@bannco.com
Technical Support
If you have any questions about your product, feel free to contact the Bannco support at support@bannco.com or browse through their website at www.bannco.com to find answers to your questions.
Warning
THIS ITEM INCLUDES THE INVISIBLE LASER COMPONENET, NEVER LOOK AT THE SENSOR DIRECTLY OR IT MAY HARM YOUR EYE. KEEP IT AWAY FROM CHILDREN.
FCC Advisory
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or move the console / PC.
- Increase the separation between the equipment and the Controller.
- Consult the dealer or an experienced radio/TV technician for help.
Product Limited Warranty
This product is warranted to the ORIGINAL purchaser for the normal intended use for a period of one year from the date of purchase. If a defect covered under this warranty occurs, we will replace or repair the product or its defective parts, at our option, at no parts and labur charge. Some shipping charge may applied. Warranty does not apply to defects resulting from modification or misuse of this product. This product can only be returned based on the policy of the place of purchase. Please allow 3-4 weeks for processing.